Roofers for Pretoria and Centurion homes, estates & complexes

Roofing guide

Why Pretoria IBR Roofs Leak at Screws and Laps

Why IBR roofs leak in Pretoria and Centurion at screws, washers, laps and flashings, and how those details should be repaired.

If you have an IBR or corrugated roof on a house, carport, garage or outbuilding in Pretoria or Centurion, and it leaks, the cause is very often not the sheet itself. It is one of the small details that hold the roof together: a screw, its washer, a lap between two sheets, or a flashing where the roof meets a wall. This guide explains why IBR roofs leak in Pretoria at those points, how to spot the signs and how the repair should be done so it lasts.

How an IBR Roof Keeps Water Out

IBR sheeting has deep, square ribs with flat pans between them. Water runs down the pans to the gutter. The sheets are fixed to the purlins with screws through the tops of the ribs, and each screw has a washer that seals the hole. Where two sheets meet side by side, one rib laps over the next; where a run is too long for one sheet, the upper sheet overlaps the lower one along the slope. Ridges, barge flashings and wall flashings close off the edges.

Every one of those joints is a place where water can get in if something is wrong. The pans themselves rarely leak unless they are rusted through or physically damaged.

Screws and Washers

Screw fixings are the most frequent leak point on sheeted roofs. Typical faults are:

  • Perished washers. The sealing washer under each screw head is exposed to strong sun all year. Over time it can harden, crack and stop sealing the hole.
  • Loose screws. Metal sheeting expands in the midday heat and contracts as it cools. That daily movement, and wind lifting the sheets, can gradually loosen fixings.
  • Over-tightened screws. A screw driven too hard crushes the washer and can dent the rib, leaving a hollow that holds water.
  • Screws in the pan instead of the rib. A fixing placed in the flat pan sits in running water every time it rains.
  • Rusted screws. Once a screw head rusts, the seal fails and rust stains spread down the sheet.
  • Old holes left open. When a satellite dish, aerial or solar bracket has been moved, the old holes are sometimes left behind.

Laps Between Sheets

Side laps and end laps leak for different reasons. On side laps, the most common problem is a sheet that has lifted or was never fixed tightly enough at the lap, so wind-driven rain is pushed across the rib. On end laps, the overlap may be too short for the pitch of the roof, or the lap may have been fixed in a way that lets water track back up between the sheets. On low-pitched carports and patios, which are common in Pretoria gardens, water drains more slowly and is more likely to work its way into any lap that is not right.

Laps also collect dirt and moisture, so rust often starts there first, out of sight on the underside of the upper sheet.

Flashings and Wall Junctions

Many Pretoria homes combine a tiled main roof with sheeted additions: a carport against the house, a covered patio, a granny flat or a lean-to. Where a sheet roof meets a wall, a flashing has to carry water away from the joint. If the flashing has pulled away from the wall, was never chased into the brickwork, or is relying on a bead of sealant that has cracked in the sun, water runs straight down the wall into the room or carport below.

Signs to Look For

  • Drips that appear at regular spacing, often in line with the purlins.
  • Rust streaks running down from screw heads.
  • Stains on a ceiling under a sheeted section, or along a wall where a lean-to roof joins the house.
  • Water on the carport floor in a line under a lap.
  • Sheets that rattle or lift in the wind.

From the ground, binoculars or a phone zoom can show rusted screw heads and lifted sheet edges without anyone going onto the roof.

How the Repair Should Be Done

A lasting repair deals with the cause rather than covering it. Depending on what is found, that can mean replacing perished or rusted screws with new fixings and washers of the right length, refixing loose sheets so the laps close properly, closing or sealing redundant holes, replacing sheets that have rusted through at the laps or have been damaged by hail, and refitting flashings so they shed water away from walls.

Smearing sealant over every screw head is not a repair. It may stop a drip for a season, but the sealant cracks in the sun and the real problem underneath remains. If a roof has many failed fixings over a large area, it is better to know that early, because replacing the fixings across a whole section is usually more economical than chasing individual leaks.

When Sheets Need Replacing

If rust has eaten through the pans, the laps have corroded on the underside, or hail has split the sheets, new fixings will not help. Replacement sheets need to match the profile of the existing roof so the laps close. On an older roof where most sheets are in poor condition, replacing a whole slope may make more sense than patching. Our re-roofing page explains what that involves.

Before You Call

It helps to note where the drips appear, whether they show only in heavy storms or in any rain, and whether there has been recent work on the roof, such as solar panels or a new satellite dish. Photos from the ground are always useful. In Centurion and Pretoria East estates, tell us the estate name so that access can be arranged. We inspect IBR and corrugated roofs across Pretoria and Centurion.

For the repair itself, see IBR and corrugated roof repairs, or send us the details.

Wet corrugated metal roof sheeting after rain

Roofing quotes

Request a Roofing Quote

Send your suburb, the roof type and a few photos of the problem area. We come back with next steps and, where needed, a time for a site visit.

Request a roofing quote →
Roofers installing metal roof panels on a house, seen from a distance
Freshly painted plaster and brick house with a metal roof and a palisade fence